Instrument sizing

How to Read Surgical Instrument Sizes and Catalog Numbers

Updated
Reading
6 min
Sources
6 cited
Written by
Medical Plus Team
Leksell rongeur, Lane bone holding forceps, Hibbs osteotome and receiving tubes from Medical Plus

Most instrument listings give two kinds of size: the overall length, in centimeters and inches, and the size of the working end in millimeters, such as a jaw, bite or blade width. Piercing items add gauge, and tubular devices may use French sizes. A catalog number then pins down the exact variant you want.

Quick answer "Leksell Rongeur, 23 cm / 9″, 3 × 13 mm bite, MP-20188" reads as: pattern name, overall length (cm, with the inch equivalent), working-end size (jaw width × jaw length) and the catalog number for that one variant. Quote the full catalog number when you order or ask for a quote.

How is instrument length given, and how do cm and inches convert?

Quick answer On our listings, length is the overall length of the instrument. One inch is exactly 25.4 mm[1], so divide centimeters by 2.54 to get inches.

Catalogs usually show the metric length first and a rounded inch figure after it. The inch value is a convenience: 15 cm works out to 5.91 inches, which is listed as 6″.

Common lengths on our listings
Listed as Exact inches (cm ÷ 2.54) Example
12 cm / 4¾″ 4.72 Kern Bone Holding Forceps (MP-19971)
15 cm / 6″ 5.91 Kern Bone Holding Forceps (MP-19972)
18 cm / 7″ 7.09 Hibbs Osteotome (MP-19551)
20.5 cm / 8″ 8.07 Stille Bone Chisel (MP-19482)
23 cm / 9″ 9.06 Leksell Rongeur (MP-20188)
24 cm / 9½″ 9.45 Hibbs Osteotome (MP-19544)
30 cm / 11¾″ 11.81 Lane Bone Holding Forceps (MP-19983-R)

How do you read jaw, bite and blade sizes?

Quick answer Working-end sizes are in millimeters. Two numbers (3 × 13 mm) usually mean width × length; one number usually means width or diameter. The listing says which.

Leksell rongeur, 23 cm, sold in bite sizes from 3 x 13 mm to 8 x 13 mm, Medical Plus
Leksell Rongeur: one 23 cm pattern, six bite sizes from 3 × 13 mm (MP-20188) to 8 × 13 mm (MP-20193).

The working-end size is usually what separates one variant from the next. The same rongeur pattern, for instance, can come in six bites that differ only in jaw width.

What the mm figure means on different instruments
Instrument Size given Example from our catalog
Rongeur Bite: jaw width × jaw length Leksell Rongeur, 3 × 13 mm to 8 × 13 mm
Osteotome, chisel, gouge Width of the cutting edge Hibbs Osteotome, 6 to 25 mm
Bone holding forceps Jaw size, where listed Verbrugge, 9.5, 10.5 and 12 mm
Bipolar / monopolar forceps Tip width Jansen Bayonet Hand Switch, 2 mm tip
Piercing forceps Jaw or hole diameter Small Nostril Forceps, Ø1, 1.2 or 1.5 mm
Receiving tube Outside / inside diameter Slant Cut Tube, e.g. OD 5 mm / ID 3.5 mm
Mallet Weight and face diameter Surgical Bone Mallet, e.g. 300 g head, 30 mm Ø

The symbol Ø means diameter. Angles (for example a 50° curve or a 45° slant cut) and words like straight, curved or curved-to-side describe the shape of the working end rather than its size.

What does gauge mean on piercing and medical items?

Quick answer Gauge is a numbered size where a higher number is thinner. Piercing jewelry in the US generally follows the American Wire Gauge; medical needle tubing has its own standard. Compare millimeters when in doubt.

In the American Wire Gauge, a larger number denotes a smaller wire[2]: 14 gauge is 0.0641 inch, or about 1.63 mm. Medical needle tubing is specified under ISO 9626, which lists designated metric sizes from 3.4 mm (10 gauge) to 0.18 mm (34 gauge)[3], whereas 10 AWG is 0.1019 inch, about 2.59 mm[2]. The same number does not mean the same diameter. Our piercing gauge size chart has the full table.

What is a French (Fr) size?

Quick answer French sizes come from Charrière's scale, which steps in thirds of a millimeter. Divide the Fr number by 3 for an approximate outside diameter in mm.

The 19th-century instrument maker Joseph-Frédéric-Benoît Charrière proposed a scale of holes that measures external size in thirds of a millimeter[4]. His gauge system, developed in 1842, is still used for catheters, probes and dilators[5]. On that basis, 9 Fr is about 3 mm and 30 Fr about 10 mm. You won't see Fr sizes on most hinged instruments, but it helps to recognize them on tubular items.

How do Medical Plus MP catalog numbers work?

Quick answer Every variant (pattern, length, working-end size and options such as a ratchet) has its own MP number. The same pattern in a different size has a different number.

Lane bone holding forceps with ratchet, catalog numbers MP-19983-R and MP-19983-NR, Medical Plus
Lane Bone Holding Forceps: the 30 cm standard version is MP-19983-R with a ratchet and MP-19983-NR without.

Our numbers start with MP- and identify one exact item. Most are numeric, and some include short suffixes or descriptive parts. Here is how to read the examples you'll meet on our listings:

Examples of Medical Plus catalog numbers
Catalog number Item What to notice
MP-19551 Hibbs Osteotome, 18 cm, straight, 6 mm One number per length and width
MP-19983-R / MP-19983-NR Lane Bone Holding Forceps, 30 cm, with / without ratchet Suffix marks an option
MP-19482 / MP-19482-ST Stille Chisel, 10 mm, standard / straight pattern Suffix marks a pattern variant
MP-6041-1P2MM Small Nostril Piercing Forceps, Ø1.2 mm "1P2MM" reads as 1.2 mm
MP-OST-HIBBS-18CM-25MM Hibbs Osteotome, 18 cm, 25 mm Descriptive code: type, pattern, length, width

What material specification should you look for?

Quick answer Our listings state surgical-grade stainless steel. If your facility needs a specific material standard, ask for it before you order.

Stainless steels for surgical instruments are covered by ASTM F899, whose current edition groups them into classes including austenitic, martensitic, precipitation-hardening and ferritic stainless steels[6]. The standard is a specification for the steel itself. If your purchasing rules ask for a material grade, email us with the catalog numbers and we'll tell you what we can confirm in writing.

What should you include when you order or ask for a quote?

  • Full catalog number, including any suffix.
  • Pattern name, overall length (cm) and working-end size (mm).
  • Options: straight or curved, ratchet or not, coating, jaw type.
  • Quantity, and whether the items must match an existing tray.
  • For piercing items, the needle gauges you use, so we can check tube and pusher fit.

Featured in this guide

Browse by category: Orthopedic, Surgical, Electrosurgical, Osteotomes, Bone Holding & Reduction Forceps and Piercing.

FAQ

Is the length measured to the tip or including the handle?

On our listings, length is the overall length of the instrument. If you need a specific working length, ask us with the catalog number.

Why do the inch figures look rounded?

Lengths are set in centimeters and the inch figure is a rounded conversion at 25.4 mm per inch[1]. For an exact match, compare the cm figure.

What does "3 × 13 mm" mean?

On a rongeur it is the bite: a jaw 3 mm wide and 13 mm long.

Can you match a catalog number from another supplier?

Often, if you send the pattern, length, working-end size and a photo. Email info@medicalplusinc.com and we'll confirm what we can supply.

Sources

  1. National Institute of Standards and Technology – SI Units: Length (undated web page). nist.gov
  2. National Bureau of Standards (now NIST) – Handbook 100: Copper Wire Tables (1966). NBS Handbook 100 (PDF)
  3. International Organization for Standardization – ISO 9626:2016, Stainless steel needle tubing for the manufacture of medical devices — Requirements and test methods (2016). iso.org
  4. Histoire des Sciences Médicales – Segal A. Charrière's scale (2016). PubMed 30005449
  5. Journal of Pediatric Urology – Bowen DK, et al. Sounds and Charrière: the rest of the story (2014). PubMed 24942595
  6. ASTM International – ASTM F899-23, Standard Specification for Wrought Stainless Steels for Surgical Instruments (2023). astm.org

General questions about ordering

Can Medical Plus instruments be autoclaved and reused?

Our stainless-steel surgical, electrosurgical and piercing instruments are made for repeated use and are compatible with standard steam sterilization (autoclaving) when they are cleaned and maintained properly. Follow the instructions supplied with the instrument and your facility's or studio's protocol, and check the Key Specs on the product page. If you are unsure about a coated instrument, contact us before autoclaving it.

What are the instruments made of?

Stainless steel, as listed in the Key Specs on each product page. Some piercing forceps and clamps have a dip-molded jaw coating in nylon or DEHP-free plastisol, and selected forceps come in gold, black or rainbow plasma finishes.

How quickly do orders ship?

Catalog orders are processed within 1–3 business days after payment confirmation. Delivery then takes 3–7 business days in the U.S. and 7–21 business days internationally. Details are in our Shipping Policy.

Do you offer bulk or volume pricing?

Yes. We quote volume pricing for hospitals, surgical centers, distributors, piercing studios and OEM partners. Email info@medicalplusinc.com or call 516-450-0879 with the catalog numbers (MP-…) and quantities you need.

Can you make a custom size, coating or private-label instrument?

Yes, subject to manufacturing feasibility and minimum order quantities. Custom OEM, private-label and large bulk orders typically take 4–10 weeks depending on complexity, materials and volume. See Custom & OEM manufacturing.

Can I get a sample before placing a larger order?

Samples are available for qualified medical facilities, distributors and OEM partners. Email info@medicalplusinc.com to request one.

What is your return policy?

Defective or damaged items reported within 7 business days of receipt can be returned if they are unused, in the original packaging and with proof of purchase. Single-use and sterilized instruments cannot be returned. Full details are in our Refund Policy.

How do I check that an instrument matches the one I already use?

Compare the pattern name, overall length and tip or jaw size on the product page with your current instrument. If you are still unsure, send us the catalog number (MP-…) and we will confirm the fit.