In the US, body jewelry and piercing needles are usually sized in gauge, and most American piercers use the Brown and Sharpe / American Wire Gauge (AWG) system[2]. The higher the gauge number, the thinner the wire[1]. This guide gives a gauge-to-millimeter chart and explains how to match needles to receiving tubes, needle pushers and tapers.
Quick answer 18g is about 1.0 mm, 16g about 1.3 mm, 14g about 1.6 mm, 12g about 2.1 mm and 10g about 2.6 mm. For a receiving tube, the needle has to pass through the tube's inner diameter (ID), so check the ID or the "accepts needles up to" size on the listing, not just the gauge stamped on the tube.
How does gauge sizing work for piercing needles and jewelry?
Gauge numbers come from wire drawing. In the American Wire Gauge, the numbers run backwards: a larger number denotes a smaller wire[1]. The scale is fixed at two ends, with No. 0000 defined as 0.4600 inch and No. 36 as 0.0050 inch, and the sizes in between follow a constant ratio[1].
Gauge is the US convention. The APP notes that most other countries measure jewelry thickness in millimeters, and above 00 gauge US sizes switch to fractions of an inch[2][3]. The steps between gauges are not even: going from 14g to 12g adds about 0.43 mm, while 4g to 2g adds about 1.36 mm[3].
What is each piercing gauge in millimeters?
Quick answer Use the chart below. Figures are the AWG diameters from the US National Bureau of Standards wire table[1], converted at exactly 25.4 mm per inch[6] and rounded to two decimals.
| Gauge | Inches | Millimeters |
|---|---|---|
| 22g | 0.0253 | 0.64 |
| 20g | 0.0320 | 0.81 |
| 18g | 0.0403 | 1.02 |
| 16g | 0.0508 | 1.29 |
| 14g | 0.0641 | 1.63 |
| 12g | 0.0808 | 2.05 |
| 10g | 0.1019 | 2.59 |
| 8g | 0.1285 | 3.26 |
| 6g | 0.1620 | 4.11 |
| 4g | 0.2043 | 5.19 |
| 2g | 0.2576 | 6.54 |
| 0g | 0.3249 | 8.25 |
| 00g | 0.3648 | 9.27 |
Suppliers sometimes list a rounded metric figure next to a gauge. Our own slant-cut receiving tubes, for example, list the 0G tube as 8 mm outside diameter, against 8.25 mm in the AWG table.
Is a piercing needle gauge the same as a medical needle gauge?
Quick answer Not necessarily. Medical needle tubing has its own sizing standard, and the same gauge number can mean a different diameter. Always compare millimeters.
Medical needle tubing is covered by ISO 9626, which specifies tubing of designated metric sizes from 3.4 mm (10 gauge) down to 0.18 mm (34 gauge)[5]. In the AWG table, 10 gauge is 2.59 mm[1]. So the gauge number alone doesn't tell you two products will fit together. If a needle, tube or piece of jewelry lists a diameter in mm, use that.
How do you match a receiving tube to your needle?
Quick answer The needle must pass through the tube's inner diameter. On our double-sided tubes the listing states the largest needle each tube accepts; on our slant-cut tubes it gives the outside and inside diameter.
Needle receiving tubes (NRTs) are used to support and protect the tissue during piercing, and they are usually hollow stainless steel tubes with smooth openings, sometimes flared or angled[2]. The gauge stamped on a tube describes the tube, not the needle it takes. That is why a "4G" tube is used with a smaller needle.

| Tube size | Double-sided 45°/30°: accepts needles up to | Slant-cut 45°: OD / ID |
|---|---|---|
| 10G | 16G (MP-6172) | Not offered |
| 8G | 14G (MP-6171) | 3 mm / 2 mm (MP-6173) |
| 6G | 10G (MP-6170) | 4 mm / 2.7 mm (MP-6174) |
| 4G | 8G (MP-6169) | 5 mm / 3.5 mm (MP-6175) |
| 2G | 6G (MP-6168) | 6 mm / 4.7 mm (MP-6176) |
| 0G | 4G (MP-6167) | 8 mm / 5.8 mm (MP-6177) |
| 00G | Not offered | 10 mm / 8 mm (MP-6178) |
To use the slant-cut column, compare the ID with the chart above. A 4G slant-cut tube has a 3.5 mm ID, and an 8g wire size is 3.26 mm, so an 8g needle of nominal size passes through.
- Double-Sided Piercing Receiving Tube – 45° & 30° Angled Ends: 0G to 10G tubes.
- Slant Cut Piercing Receiving Tube – 45°: 8G to 00G tubes, OD and ID listed.
- Flared Piercing Receiving Tube – 77 mm: listed by diameter from Ø3 mm to Ø8 mm (MP-6179 to MP-6184). Ask us for the ID of a specific size if you need it.
Which needle pusher and taper sizes do you need?
Quick answer Pick a needle pusher whose gauge range covers the needles you use, and choose tapers by millimeter size to match the jewelry.

- The Needle Pusher – 20G to 8G (MP-6185) presses on the needle hub for 20G to 8G needles.
- The Large Gauge Needle Pusher – 18G to 4G (MP-6163) covers 18G through 4G, so it is the one to choose if you work at 6G or 4G.
- Tapers are usually sized in millimeters. The Colour Taper Insertion Pin Set (MP-6071) runs from 1.2 mm to 10 mm; use the chart above to find the gauge equivalent. More options are in Piercing Tapers.
What should a studio check before ordering?
- Gauge range. List the needle gauges you actually pierce with, then pick tubes, pushers and tapers that cover them.
- Millimeters. Where a listing gives OD and ID, compare those with the chart rather than relying on the gauge label.
- Labeling. The APP manual says sterilized needles should be individually packaged and labeled with gauge and date of sterilization[2].
- Sterility. The APP states that all tools, needles and jewelry must be sterile, and all needles must be single-use[4].
- Tube material. The APP manual notes that glass and plastic tubes can become compromised and should be treated as single-use[2]. Our tubes are stainless steel and reusable when cleaned and sterilized according to your protocol.
Featured in this guide
Slant Cut Piercing Receiving Tube – 45°MP-6173–MP-6178
Double-Sided Piercing Receiving TubeMP-6167–MP-6172
Flared Piercing Receiving Tube – 77 mmMP-6179–MP-6184
Needle Pusher – 20G to 8GMP-6185
Large Gauge Needle Pusher – 18G to 4GMP-6163
See the full ranges in Piercing Receiving Tubes, Piercing Tapers and the wider Piercing collection.
FAQ
Does a lower gauge number mean a thicker needle?
Yes. In the American Wire Gauge a larger number denotes a smaller wire[1], so 12g is thicker than 14g.
Is 0g the same as 8 mm?
Close, but not exact. In the AWG table 0 gauge is 8.25 mm[1]. Some listings round to 8 mm, so check the millimeter figure when fit matters.
Why does a "4G" receiving tube take an 8G needle?
The gauge names the tube, and the needle has to fit inside it. Our listings give either the largest needle each tube accepts or the tube's inner diameter.
Can I reuse receiving tubes?
Our stainless steel tubes are reusable when cleaned and sterilized according to your protocol. Needles are single-use[4], and the APP manual suggests treating glass and plastic tubes as single-use[2].
Sources
- National Bureau of Standards (now NIST) – Handbook 100: Copper Wire Tables (1966). NBS Handbook 100 (PDF)
- Association of Professional Piercers – Procedure Manual, 2013 Edition (2013). APP Procedure Manual (PDF)
- Association of Professional Piercers – Stretching (undated web page). safepiercing.org
- Association of Professional Piercers – Piercing FAQ (undated web page). safepiercing.org
- International Organization for Standardization – ISO 9626:2016, Stainless steel needle tubing for the manufacture of medical devices — Requirements and test methods (2016). iso.org
- National Institute of Standards and Technology – SI Units: Length (undated web page). nist.gov