Orthopedic

Osteotomes vs Chisels vs Gouges: How to Tell Them Apart

Updated
Reading
7 min
Sources
6 cited
Written by
Medical Plus Team
Hibbs osteotome, Stille chisel, Lambotte osteotome, Smith-Petersen gouge and bone mallet from Medical Plus

An osteotome, a bone chisel and a gouge are all bone-cutting blades driven with a mallet, and the quickest way to tell them apart is the cutting edge. An osteotome is beveled on both sides of its edge[1]. In most instrument catalogs, including ours, a chisel is sharpened from one side only, and a gouge has a curved, trough-shaped blade.

Quick answer Look at the tip. Bevels on both faces: osteotome. One flat face and one bevel: chisel. A curved blade that forms a channel: gouge. Then choose width, length and straight or curved to suit the procedure, and pair the set with a mallet.

What is the difference between an osteotome, a chisel and a gouge?

All three are hand-held blades that a surgeon drives with a mallet to cut, chip or shape bone. The difference is in how the cutting edge is ground and whether the blade is flat or curved. A peer-reviewed description puts it simply: the osteotome resembles a chisel but is beveled on both sides of the cutting edge[1].

The names are not fully standardized between manufacturers. A professional dental glossary, for example, defines a chisel only as an instrument with a beveled cutting edge used for cutting or cleaving hard tissue[6], without saying how many bevels it has. So use the table below as a guide, and always check the photo and specifications on the listing.

Osteotome vs chisel vs gouge at a glance
Instrument Blade and edge How to spot it Examples in our catalog
Osteotome Flat blade, beveled on both sides of the edge Edge sits in the middle of the blade's thickness Hibbs, Lambotte, Smith-Peterson, Cottle, Stille
Bone chisel Flat blade, usually beveled on one side One face stays flat right to the edge Stille, Partsch, Cottle fishtail, Alexander
Gouge Curved, trough-shaped blade Looking end-on, the edge is a curve, not a straight line Smith-Petersen, Stille, Lexer, Cobb spinal

How do you identify an osteotome?

Quick answer Turn the blade side-on. If both faces taper toward the edge, it is an osteotome.

Hibbs osteotome, straight stainless steel blade, Medical Plus
Hibbs Osteotome: a straight osteotome offered in 18 cm and 24 cm lengths and widths from 6 to 25 mm.

Osteotomes are used to chip, cut and sculpt bone in orthopaedic, plastic and dental surgery[1]. In rhinoplasty, for example, lateral osteotomies are performed with osteotomes to close an open roof, narrow the upper third or correct a deviated bony nose[2].

  • The Hibbs Osteotome comes in 18 cm / 7″ and 24 cm / 9½″ lengths, straight, in widths from 6 mm to 25 mm (for example MP-19551 is 18 cm × 6 mm).
  • The Lambotte Osteotome covers a wide range: straight blades from 3 mm, and curved 24 cm blades from 15 mm to 50 mm.
  • Sets such as the Hibbs Osteotome Set and Stille Osteotome Set group several widths for one tray.

Facial and maxillofacial patterns, such as the Cottle, Obwegesser and Tessier osteotomes, are in the same Osteotomes collection.

How do you identify a bone chisel?

Quick answer On a chisel, one face of the blade stays flat right up to the edge and the bevel is ground on the other face.

Stille bone chisel with hexagonal handle, Medical Plus
Stille Bone Chisel: a flat blade on a hexagonal handle, 20.5 cm long, in widths from 8 to 25 mm.

Holding a chisel against the light, you can see the flat back running straight to the edge. That one-sided grind is the main thing to check when you compare a chisel with an osteotome of the same width.

You'll find all of them in Bone Chisels & Gouges.

How do you identify a gouge?

Quick answer Look at the blade end-on. A gouge's edge is curved, so the blade forms a channel or scoop.

Smith-Petersen gouge with curved blade and round handle, Medical Plus
Smith-Petersen Gouge: 20 cm long, straight or curved, in widths from 9 to 25 mm.

Because the edge is curved, a gouge cuts a curved channel rather than a straight line. Osteotomes and gouges together are described as the standard method for harvesting iliac crest bone graft[3], one example of a procedure that uses both.

Which mallet should you pair with them?

Quick answer Any of these blades is struck with a surgical mallet. Choose the head weight and face your surgeons prefer for the size of the blades on the tray.

Surgical bone mallet, stainless steel, Medical Plus
Surgical Bone Mallet: offered from a 300 g head up to 900 g overall.

The mallet is part of how the cut is controlled. In a published rhinoplasty technique, the surgeon notes that the pitch of the mallet striking the osteotome changes from high to low as the bone gives way[2].

How do you choose width, length and curve?

Quick answer Width (in mm) sets the cut; length sets the reach; straight or curved sets the angle of approach. Most trays carry a run of widths in one pattern.

  1. Width. The number in mm on the listing is the width of the cutting edge. Fine work uses narrow blades: one rhinoplasty review discusses 2, 3 and 4 mm osteotomes, guarded or unguarded[2]. Long-bone work uses much wider blades.
  2. Length. Overall length, given in cm and inches (for example 24 cm / 9½″). Choose the shortest length that reaches the site comfortably.
  3. Straight or curved. Curved osteotomes and gouges change the angle of the cut. Our Lambotte and Smith-Petersen listings offer both.
  4. Handle. Some patterns are one-piece steel, others have a separate handle, such as the hexagonal handle on our Stille chisel. Check that the striking end suits your mallet.
  5. Sets vs singles. A set gives a matched run of widths; singles let you replace one size.

How do you keep cutting edges in shape?

Quick answer Inspect the edge at every reprocessing cycle, protect it in the tray, and send blades for sharpening or replacement when they no longer pass inspection.

Osteotomes are commonly reused in orthopedic surgery[4], so edge wear builds up over time. In a laboratory study of rhinoplasty osteotomes, cutting performance decreased significantly with use, and professional sharpening only achieved results similar to an osteotome used 3 to 6 times[5]. Another study found that a measured sharpness index detected cutting-edge wear better than visual inspection[4], so a quick glance may not show everything.

  • Check edges for nicks, rolled edges and chips after cleaning.
  • Store blades so edges don't touch other instruments.
  • Follow the instrument's IFU and your facility's protocols for cleaning, sterilization and repair.

Featured in this guide

Browse the full ranges in Osteotomes, Bone Chisels & Gouges and Surgical Mallets.

FAQ

Is an osteotome just a type of chisel?

It is closely related. An osteotome resembles a chisel but is beveled on both sides of the cutting edge[1], while catalogs usually reserve "chisel" for a blade sharpened from one side.

What does the mm size on an osteotome or gouge mean?

It is the width of the cutting edge. The second figure on our listings is the overall length, in cm and inches.

Can osteotomes be resharpened?

Many reusable osteotomes are sharpened or repaired, but one study found professional sharpening restored performance only to the level of an osteotome used 3 to 6 times[5]. Follow the IFU and your facility's repair policy, and replace blades that no longer pass inspection.

When would I choose a gouge instead of an osteotome?

When you need a curved cut. An osteotome is a flat blade beveled on both sides of the edge, while a gouge has a curved, trough-shaped blade, so it cuts a curved channel rather than a straight line. Osteotomes and gouges together are described as the standard method for harvesting iliac crest bone graft[3].

Sources

  1. PLOS ONE – White DE, et al. Pilot study: post-surgical infections could be related with lack of sharpness in surgical tools (2022). PMC8809569
  2. GMS Current Topics in Otorhinolaryngology, Head and Neck Surgery – Tasman AJ. Rhinoplasty: indications and techniques (2007). PMC3199847
  3. Orthopaedic Review – Duncan RW, McGuire RA, Meydrech EF. Pneumatic gouge versus standard method for iliac crest harvesting (1994). PubMed 7997351
  4. Journal of Orthopaedic Surgery and Research – White DE, et al. Pilot investigation into osteotome hard surface coating and cutting-edge degradation (2020). PMC7350671
  5. Archives of Facial Plastic Surgery – Bloom JD, Ransom ER, Antunes MB, Becker DG. Quantifying the sharpness of osteotomes for dorsal hump reduction (2011). PubMed 21422444
  6. International Congress of Oral Implantologists – Glossary: Chisel (undated web page). icoi.org

General questions about ordering

Can Medical Plus instruments be autoclaved and reused?

Our stainless-steel surgical, electrosurgical and piercing instruments are made for repeated use and are compatible with standard steam sterilization (autoclaving) when they are cleaned and maintained properly. Follow the instructions supplied with the instrument and your facility's or studio's protocol, and check the Key Specs on the product page. If you are unsure about a coated instrument, contact us before autoclaving it.

What are the instruments made of?

Stainless steel, as listed in the Key Specs on each product page. Some piercing forceps and clamps have a dip-molded jaw coating in nylon or DEHP-free plastisol, and selected forceps come in gold, black or rainbow plasma finishes.

How quickly do orders ship?

Catalog orders are processed within 1–3 business days after payment confirmation. Delivery then takes 3–7 business days in the U.S. and 7–21 business days internationally. Details are in our Shipping Policy.

Do you offer bulk or volume pricing?

Yes. We quote volume pricing for hospitals, surgical centers, distributors, piercing studios and OEM partners. Email info@medicalplusinc.com or call 516-450-0879 with the catalog numbers (MP-…) and quantities you need.

Can you make a custom size, coating or private-label instrument?

Yes, subject to manufacturing feasibility and minimum order quantities. Custom OEM, private-label and large bulk orders typically take 4–10 weeks depending on complexity, materials and volume. See Custom & OEM manufacturing.

Can I get a sample before placing a larger order?

Samples are available for qualified medical facilities, distributors and OEM partners. Email info@medicalplusinc.com to request one.

What is your return policy?

Defective or damaged items reported within 7 business days of receipt can be returned if they are unused, in the original packaging and with proof of purchase. Single-use and sterilized instruments cannot be returned. Full details are in our Refund Policy.

How do I check that an instrument matches the one I already use?

Compare the pattern name, overall length and tip or jaw size on the product page with your current instrument. If you are still unsure, send us the catalog number (MP-…) and we will confirm the fit.