Orthopedic

Bone Curettes Explained: Volkmann, Bruns, Spratt & Sizes

Updated
Reading
7 min
Sources
6 cited
Written by
Medical Plus Team
Volkmann, Bruns, Halle, Williger, Schede, USA pattern and Simon bone curettes from Medical Plus

A bone curette is a hand instrument with a sharp-edged cup on the end of a shaft, used to scrape and scoop bone, granulation tissue and debris. Volkmann, Bruns, Spratt and the other named patterns mostly differ in overall length, cup shape, single or double ends and whether the shank is straight or angled. Within each pattern, the "Fig." number is the cup-size step.

Quick answer Pick the reach first (about 13–17 cm for shallow, open work; 21–28 cm for deeper cavities), then straight or angled, then the cup size. Fig. sizes are a step within each pattern and are not standardized between makers, so match against a set you already use or ask us for the cup dimension.

What is a bone curette used for?

Quick answer Scraping. The sharpened rim of the cup lifts away soft tissue, cancellous bone or debris, and the cup holds what it removes.

Two common orthopedic uses show up clearly in the literature:

  • Clearing out a bone lesion. A published technique for benign cystic bone lesions tells surgeons to "use curets, rongeurs, or spoons to remove all contents from the cavity," and to confirm the whole cavity can be reached with the curet[1]. For giant cell tumor of bone, StatPearls lists curettage, curettage with bone grafting and curettage with bone cement among the treatment options[2].
  • Harvesting cancellous bone graft. In a 2023 cadaveric study of anterior iliac crest harvesting, the cancellous bone was taken with "a sharp surgical curette with a cup size of 8 mm"[3]. The same study found a trephine collected more bone volume than the curette technique, so the curette is one option among several[3].

Which technique and instrument to use is a clinical decision for the surgeon. This guide only helps you identify and order the right pattern and size.

How do Volkmann, Bruns, Spratt and other patterns differ?

Quick answer By length, number of working ends, cup shape and shank angle. Compare the photo and catalog number, not just the name.

The names are traditional pattern names. The table below uses the sizes listed in our own catalog.

Bone curette patterns we list
Pattern Length(s) Ends Options Fig. sizes
Volkmann 17 cm (6¾″), 27 cm (10¾″) Single Stainless or Ferrozell handle 0000–6
Volkmann double-ended 13–20 cm (5″–8″) Double Style A or Style B Sold by length and style
Bruns 17 cm (6¾″), 23 cm (9″) Single Straight; 45° angled on the 23 cm 0000–6
Spratt 17 cm (6¾″) Single One style 0000–6
Williger 13.5 cm (5¼″), 17.5 cm (7″) Double or single Oval cup or round cup 0/0–1/2 (double); 00–2 (single)
Cobb 28 cm (11″) Single Straight or 45° angled 000–6
Simon 24 cm (9½″) Single One style 1–6
Halle 21 cm (8¼″) Single One style 1–3
Volkmann bone curette with oval cup and fluted stainless steel handle, Medical Plus
Volkmann Bone Curette: 17 cm or 27 cm, in Fig. 0000 to Fig. 6.
Bruns bone curette, stainless steel, Medical Plus
Bruns Bone Curette: 17 cm straight, or 23 cm straight or angled 45°.
Spratt bone curette, stainless steel, Medical Plus
Spratt Bone Curette: 17 cm, offered in ten Fig. sizes.

When does a double-ended curette make sense?

Quick answer When you want two cups on one instrument and fewer instruments on the tray. Single-ended curettes give you the full handle to grip.

Williger double-ended bone curette with a cup at each end and a knurled center grip, Medical Plus
Williger Bone Curette, double-ended: a working cup at each end of the grip.

A double-ended curette usually pairs two different cup sizes or shapes. Our double-ended options are the Williger (13.5 cm, Fig. 0/0, 0/1 and 1/2), the Volkmann double-ended (13–20 cm, Style A or B) and the Martini double-ended (14 cm or 21 cm).

What do Fig. sizes and cup sizes mean?

Quick answer "Fig." is the catalog size step for the cup within one pattern. Order by catalog number, and ask us for the cup dimension if millimetres matter.

Our Volkmann, Bruns and Spratt curettes are listed from Fig. 0000 through Fig. 6, Cobb from Fig. 000 through Fig. 6, and Simon from Fig. 1 through Fig. 6.

  • Fig. sizes are not a universal standard. The same Fig. number can mean a different cup width from another maker, or even between two patterns.
  • Clinical papers usually give millimetres, not Fig. numbers. The graft study above names an 8 mm cup[3]. If you need a set cup diameter, contact us with the dimension and we will confirm which catalog number is closest.
  • Order by catalog number. Each size has its own MP number (for example, the Spratt Fig. 0 is MP-19247), which avoids mix-ups when reordering.

Straight, angled or reverse angled: which shank do I need?

Quick answer Straight for surfaces in line with the shaft, angled for side walls, reverse angled for undercuts you work toward yourself.

Shank angles compared
Shank Where it reaches Where we offer it
Straight Surfaces directly in line with the shaft Listed as an option on Bruns, Cobb, Long Shaft and USA Pattern
Angled (45° or "B") Side walls of a cavity Bruns 23 cm, Cobb, Long Shaft, USA Pattern
Reverse angled ("C") Undercuts and back walls, working toward you Long Shaft, USA Pattern
USA pattern bone curette, straight shank, stainless steel, Medical Plus
Bone Curette, USA Pattern (straight shown): also offered angled and reverse angled, Fig. 1 to Fig. 6.

Deep cavities may also call for a long pattern such as the 25 cm Long Shaft curette or the 28 cm Cobb curette.

How should reusable curettes be cleaned and inspected?

Quick answer Clean first, inspect inside the cup, then sterilize, following the instrument's instructions for use and your facility's protocols.

A curette is a critical item because it enters sterile tissue. CDC guidance says objects that enter sterile tissue "must be sterile because any microbial contamination could transmit disease"[4]. The cup traps bone and tissue, so cleaning matters before any sterilization step:

  1. Clean first. CDC states that "thorough cleaning is required before high-level disinfection and sterilization," and advises presoaking or rinsing surgical instruments so blood does not dry on them[5].
  2. Inspect every instrument. CDC says all instruments "should be individually inspected and be visibly clean"[5]. On a curette, look inside the cup and along the rim.
  3. Follow the labeling. FDA describes reprocessing as a multistep process of cleaning, then disinfection or sterilization, following the device's labeling instructions[6].

For more detail, see our guide on caring for reusable stainless steel instruments.

Featured in this guide

Browse the full range in Bone Curettes, or see Bone Rongeurs for the instruments often used alongside them.

FAQ

Is a Volkmann curette the same as a Bruns or Spratt curette?

No. They are separate patterns. They do the same basic job of scraping bone with a cup, but differ in length, size range and shank options. Compare the product photos and catalog numbers rather than the name alone.

Does a higher Fig. number mean a bigger cup?

Fig. numbers are a size step within one pattern, but they are not standardized across manufacturers. If cup diameter matters, ask us for the dimension before ordering.

Should I choose single-ended or double-ended?

Double-ended curettes give two working ends on one instrument and can reduce tray count. Single-ended curettes give you the whole handle to grip.

What is a Ferrozell handle?

Our Volkmann curette is offered with either an all-stainless handle or a Ferrozell handle. Check the instructions for use for any reprocessing limits that apply to the handle material.

Do I need a straight, angled or reverse-angled curette?

A straight shank reaches surfaces directly in line with the shaft, an angled shank reaches the side walls of a cavity, and a reverse-angled shank reaches undercuts and back walls, working toward you.

Sources

  1. JBJS Essential Surgical Techniques – Ibe IK, Alder KD, Henderson SE, Yu KE, Lee FY. Excisional Curettage of Benign Cystic Lesions (2019). PMC6948994
  2. NCBI Bookshelf / StatPearls – Giant Cell Tumor (Osteoclastoma) (last updated 2024). NBK559229
  3. Chinese Journal of Traumatology – Cakar A, et al. Comparison of curettage vs. trephination technique for harvesting anterior iliac crest bone graft: A cadaveric study (2023). PMC11973664
  4. Centers for Disease Control and Prevention – A Rational Approach to Disinfection and Sterilization, Guideline for Disinfection and Sterilization in Healthcare Facilities (2008). cdc.gov
  5. Centers for Disease Control and Prevention – Cleaning, Guideline for Disinfection and Sterilization in Healthcare Facilities (2008). cdc.gov
  6. U.S. Food and Drug Administration – Reprocessing of Reusable Medical Devices (2023). fda.gov

General questions about ordering

Can Medical Plus instruments be autoclaved and reused?

Our stainless-steel surgical, electrosurgical and piercing instruments are made for repeated use and are compatible with standard steam sterilization (autoclaving) when they are cleaned and maintained properly. Follow the instructions supplied with the instrument and your facility's or studio's protocol, and check the Key Specs on the product page. If you are unsure about a coated instrument, contact us before autoclaving it.

What are the instruments made of?

Stainless steel, as listed in the Key Specs on each product page. Some piercing forceps and clamps have a dip-molded jaw coating in nylon or DEHP-free plastisol, and selected forceps come in gold, black or rainbow plasma finishes.

How quickly do orders ship?

Catalog orders are processed within 1–3 business days after payment confirmation. Delivery then takes 3–7 business days in the U.S. and 7–21 business days internationally. Details are in our Shipping Policy.

Do you offer bulk or volume pricing?

Yes. We quote volume pricing for hospitals, surgical centers, distributors, piercing studios and OEM partners. Email info@medicalplusinc.com or call 516-450-0879 with the catalog numbers (MP-…) and quantities you need.

Can you make a custom size, coating or private-label instrument?

Yes, subject to manufacturing feasibility and minimum order quantities. Custom OEM, private-label and large bulk orders typically take 4–10 weeks depending on complexity, materials and volume. See Custom & OEM manufacturing.

Can I get a sample before placing a larger order?

Samples are available for qualified medical facilities, distributors and OEM partners. Email info@medicalplusinc.com to request one.

What is your return policy?

Defective or damaged items reported within 7 business days of receipt can be returned if they are unused, in the original packaging and with proof of purchase. Single-use and sterilized instruments cannot be returned. Full details are in our Refund Policy.

How do I check that an instrument matches the one I already use?

Compare the pattern name, overall length and tip or jaw size on the product page with your current instrument. If you are still unsure, send us the catalog number (MP-…) and we will confirm the fit.